Gate Installation in New Braunfels - Free Estimate, One Written Price

Trusted Gate Installation for New Braunfels Homeowners

Building a gate from scratch means decisions about posts, swing or slide, and how the operator gets its power – and getting any of those wrong shows up later as sagging hardware or an operator that fights the gate. We install new gates with the same brand-agnostic approach we bring to gate repair in New Braunfels: we look at your driveway, your fence line, and the brand of equipment you’re considering, then tell you what will hold up. Our technicians have up to 14 years of experience and work with DoorKing, Elite, and Mighty Mule equipment across residential and commercial jobs. This isn’t same-day work – new gates are measured, ordered, and scheduled – but a free on-site measure and a written price come first. Call (855) 939-0250. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

Call (855) 939-0250

Automatic Gate Installation

Automatic Gate Installation covers the full package: the gate itself, the operator, the safety edges or loops, and the control wiring that ties it together. You need it when you want the gate to open on a remote or keypad without anyone stepping out of the car, or when an old manual gate is being replaced by an automated one. We handle the gate and the automation together, so there’s no handoff between a gate fabricator and an operator installer. A full automated installation typically runs $3,500-$9,000 depending on gate size, material, and operator class, with the written estimate setting the final price.

Gate, Operator, and Controls Together

We install the swinging or sliding leaf, mount the operator, and wire the control board, receiver, and safety devices as one job. That means the travel limits, the reverse sensitivity, and the access control are all set by the same gate technicians. Nothing gets left for somebody else to finish.

What a Typical Automated Job Involves

We measure the opening and check the soil and slope where the posts will go, then confirm the operator model and power source. On install day the posts go in, the gate hangs, and the operator gets set up and tested through several full cycles. Expect the gate to be ordered and scheduled rather than installed same-day.

Gate Installation Services

Gate Installation Services covers swing gates, slide gates, pedestrian access gates, and the operators that drive them, whether you’re replacing a worn-out gate or starting from bare ground. You need them when a gate has been damaged beyond sensible repair, when a property’s access layout changes, or when a new driveway or fence line requires a gate that didn’t exist before. We keep our work to gates only, so a gate call is never secondary work for the technicians. Typical gate installation services in New Braunfels run $1,800-$6,500 depending on the gate type, span, and whether an operator is part of the job. The written estimate fixes the number before anything is ordered.

Swing and Slide, Residential and Commercial

Residential swing gates and heavier commercial slide gates ask for different posts, hinges, and operators, and we install both. We also work on barrier arms and access-controlled entrances, so an HOA or small commercial property doesn’t need a second company for the gate at the entrance. Every job is measured first.

Replacing a Gate That’s Past Repair

Sometimes the honest answer is a new gate rather than another round of repairs. We’ll tell you which side of that line your gate sits on and explain what a repair would and wouldn’t fix. If replacement makes more sense, we quote the new gate and operator on the same visit.

Electric Gate Installation

Electric Gate Installation is the powered side of a gate project: the operator, the wiring, the control board, and the safety devices that make an automated gate safe to leave running. You need it when a manual gate should open itself, when a property adds access control, or when an existing operator has reached the point where a new one is the smarter spend. Electric gate repair is a named specialty of ours, so we install operators with the same attention to control and power we bring to fixing them. Budget-wise, electric gate installation typically runs $2,200-$7,500 depending on operator class, gate weight, and the distance to the power source, with the written estimate setting the price.

Operator Class and Gate Weight

A light residential operator and a commercial-grade DoorKing unit aren’t interchangeable, and the gate’s weight and daily cycle count decide which one fits. We size the operator to the gate rather than the other way around. That keeps the motor from working harder than it should.

Power Runs and Safety Devices

Getting power to the operator is often the part homeowners underestimate, especially when the gate sits well off the house. We plan the power run, then install and test the safety edges, photo eyes, or loops so the gate reverses when something is in its path. This is licensed electrical-adjacent work and belongs with a trained technician, not a weekend project.

Driveway Gate Installation

Driveway Gate Installation is a new gate for the vehicle entrance, sized to your driveway width, slope, and turning room. You need it when a property has no gate at the drive, when an old gate is too narrow or too short for the vehicles using it, or when a driveway is being widened or re-routed. We measure the opening on site and account for how the ground falls, since a sloped drive changes the post depth and the operator choice. Driveway gate installation in New Braunfels typically runs $2,500-$8,000 depending on material, span, and whether the gate is automated. The written estimate sets the final number.

Sizing the Gate to the Drive

Clearance matters more than most people expect, especially for trucks and trailers. We measure the widest vehicle that will use the drive and leave room for the swing or slide path. The gate is built to that opening, not to a stock size.

Posts, Footing, and Slope

Posts go to a proper footing depth for the gate’s weight and the soil here, and a sloped drive gets posts set to keep the leaf level through its travel. That groundwork is what keeps a heavy gate from sagging within a season. We check the ground before quoting.

Sliding Gate Installation

Sliding Gate Installation is a gate that rolls sideways along a track instead of swinging out, which suits drives where a swing would block a slope, a fence line, or a tight turning area. You need it when a swing gate won’t fit the space, when the drive is steep, or when a commercial entrance sees enough traffic that a slide makes more sense. We set the track, the rollers, and the operator so the gate tracks true through its whole travel. Sliding gate installation typically runs $3,000-$9,500 depending on span, gate weight, and operator class. The written estimate fixes the price before work starts.

Track and Roller Setup

A slide gate is only as good as its track. We set the track level and anchored, then align the rollers so the gate doesn’t bind or walk off the end of its run. A slide gate that comes off the track is a heavy panel in motion, which is why we take the alignment seriously.

When a Slide Beats a Swing

If your drive climbs, or a swing gate would sweep into the street or a fence, a slide usually wins. We’ll walk the layout with you and say plainly which type fits your property. The measure and the quote come before any order.

Gate Opener Installation

Gate Opener Installation is fitting a new operator to an existing or new gate, including the arm or slide mechanism, the control board, the receiver, and the safety devices. You need it when a gate is manual and you want it automated, or when an old operator has failed and a new one is the better spend than another repair. We work with the brand you already have or the one you’re considering, from Mighty Mule residential units up to LiftMaster and commercial-grade operators. Gate opener installation typically runs $1,400-$4,500 depending on the operator class and the gate it’s driving, with the written estimate setting the final price.

Matching the Opener to the Gate

An operator sized for a light gate will strain on a heavy one and wear out early. We check the gate’s weight, its swing or slide path, and how often it opens before recommending a model. That’s the same logic we use when an operator fails and repair versus replace comes up.

Remotes, Keypads, and Access Control

Opener installation includes the access side: remotes, a keypad, and where it makes sense, an intercom or card reader. We set the receiver and test every entry method before we call the job done. If you’re adding access control to a shared entrance, we plan it into the same visit.

Gate Fabrication

Gate Fabrication is building a gate to fit an opening that stock sizes won’t cover, whether that’s an unusual span, a specific look, or a heavier panel for a commercial entrance. You need it when your opening is wider than standard, when an existing gate has to match a fence or architecture, or when a property needs a gate that carries more weight than an off-the-shelf unit. We fabricate to the measured opening and then install the gate and its operator as one job. Custom fabrication typically runs $2,800-$10,000 depending on material, span, and finish, with the written estimate setting the price per job.

Custom Spans and Materials

A wide opening, a specific material, or a design that has to match an existing fence line all point to a fabricated gate. We build to the measured opening so the gate hangs true and the operator isn’t fighting a warp. Material choice gets settled at the measure.

Heavy Panels and Commercial Entrances

Commercial entrances and HOA gates often need a heavier panel than residential work, and that weight has to be matched by the posts and the operator. We plan all three together. A heavy panel on undersized hardware is where trouble starts.

Brands We Service

We work on the brand you already have, and that ranges from entry-level residential units to professional-grade commercial operators. DoorKing equipment shows up on shared entrances and access-controlled drives, and we know its control and loop logic well. Elite operators are common on residential swing and slide gates, and we’re familiar with where their arms and limits wear. Mighty Mule is a popular DIY-grade residential line, and we can take over a job a homeowner started or service a unit that’s acting up.

LiftMaster covers residential and light commercial operators, and we handle their control boards, receivers, and safety devices regularly. Whether you have LiftMaster or any other make, we can help – our approach is brand-agnostic on purpose, because a technician who only knows one brand is more likely to push a replacement you don’t need.

Signs You Need a Pro Right Now

• The gate reverses or stops mid-travel. Intermittent travel usually points to a limit switch, a sensor, or a control board fault. Left alone, it tends to fail open or fail closed at the worst moment.
• The operator hums but the gate doesn’t move. That’s often a motor, capacitor, or drive-arm problem rather than a dead unit. A diagnostic visit tells you whether it’s a repair or a replacement.
• A slide gate comes off its track. A heavy panel off the track can drop or swing into a vehicle, so stop using the gate until a technician looks at it. Don’t try to muscle it back on.
• Safety edges or photo eyes aren’t stopping the gate. If the gate closes on an obstruction without reversing, the safety devices have failed. That’s a genuine hazard for people and pets, not a nuisance.
• Sparks, a burning smell, or tripped breakers at the operator. Electrical faults at the control board are dangerous and belong with a trained technician. Don’t open the control box to investigate.

Our Process, Step by Step

1. 1
   Free on-site measure. We measure the opening, check the slope and soil where posts go, and look at the power source. This visit is where we confirm swing or slide, gate size, and operator class.
2. 2
   Written estimate. You get a written price covering the gate, the operator, the wiring, and the safety devices, so nothing gets added later. The price is quoted and agreed before any work starts.
3. 3
   Ordering and scheduling. Fabricated or ordered gates take time to arrive, so this is a scheduled job, not a same-day call. We confirm the schedule once the materials are in.
4. 4
   Installation. Posts go to proper footing depth, the gate hangs and is checked for true travel, then the operator and controls are mounted and wired. On a powered gate we plan the power run and test the safety edges and photo eyes before anything else.
5. 5
   Testing and walkthrough. We run the gate through full open-close cycles, set the travel limits and reverse sensitivity, and test every remote and keypad. We walk you through the controls and the safety features before we leave.

How Much Does Gate Installation Cost in New Braunfels?

Our Service Area Near New Braunfels

We work across New Braunfels and the nearby towns, including Wimberley, Cibolo, Seguin, Schertz, Canyon Lake, Universal City, San Marcos, Converse, and Bulverde. Drive times vary by location, but fast dispatch from 7am to 7pm covers most of the area for repair calls, while installations are scheduled around the measure and the materials. If your property sits on the edge of the area, call and we’ll confirm coverage. Call (855) 939-0250. We answer 24/7.

Frequently Asked Questions About Gate Installation in New Braunfels

Schedule Your Gate Installation Service in New Braunfels Today

Ready to put in a new gate or automate the one you have? Call (855) 939-0250 for a free on-site measure and a written estimate. We’ll walk your opening, confirm swing or slide, and give you a clear price before anything is ordered. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Gate installs, gate repair, and New Braunfels access control – all under one gate specialist.

Written by the team at Gate Repair New Braunfels.