Gate Repair in New Braunfels - Fixed Today, No Surprise Invoice

Trusted Gate Repair for New Braunfels Homeowners

A gate that won’t open is more than an errand problem. It’s a security gap, a driveway you can’t get down, and a piece of hardware that usually fails at the worst moment. Gate Repair New Braunfels exists for exactly this: we’re gate specialists, not a general repair outfit that treats a stuck swing arm as a side job. Our technicians have up to 14 years of experience, and they’re trained to work on the brand you already have instead of steering you toward a replacement you don’t need. Same-day service is available in New Braunfels for most repair calls, and every price is quoted and agreed before any work starts. Call (855) 939-0250 to describe what your gate is doing. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

Call (855) 939-0250

Key Takeaways

• Gate repair in New Braunfels typically runs $150-$650 depending on the part and the hardware.
• Most calls are diagnostic: a dead operator, a sensor fault, a bent hinge, a gate that drags.
• We service nine gate brands, from Mighty Mule residential kits to DoorKing commercial operators.
• You get a free estimate and a written price before any work begins.

Driveway Gate Repair

Driveway Gate Repair is what we do when a gate blocks your actual vehicle access and can’t be ignored until next month. Common causes in New Braunfels: a swing operator that stopped responding after a thunderstorm, a sagging hinge from a post that settled in our clay-heavy soil, or a gate that opens partway and stalls. Driveway gates take more force and more daily cycles than a pedestrian gate, so the hardware wears faster and the alignment drifts sooner. Our technicians diagnose the mechanical side and the control side together, because a gate that stops halfway is often a limit-switch or control board problem, not a motor problem. Typical driveway gate repair in New Braunfels runs $180-$550 depending on the operator brand, the part, and whether the gate needs realignment. We quote the price and you approve it before anything is touched.

Operator and Motor Faults

Most driveway gate failures start at the operator, not the gate itself. We test the motor, the control board, and the limit switches to see which component actually failed, so you’re not paying for a full operator replacement when a board is the only thing wrong. If the unit is a Mighty Mule or LiftMaster, we know the failure points on both.

Post and Hinge Alignment

When a gate sags or swings crooked, the cause is usually the hinge or the post, not the operator. Texas soil shifts with seasonal moisture, and a post that has moved a fraction of an inch will throw a gate off its arc over time. We check plumb, hinge wear, and gate clearance before recommending any repair.

Gate Welding

Gate Welding is the repair of the metal frame itself: cracked welds, broken hinge mounts, snapped pickets, and failed joints where the gate meets the post. You need it when the gate has physical damage the operator can’t compensate for, like a weld that let go at a bottom rail or a hinge bracket that tore off the frame. We weld on steel and iron gates, repair broken frames, and reinforce the spots where a gate takes the most stress. If the gate is a sliding unit, welding may be the only way to keep the carriage from pulling free. Gate welding in New Braunfels typically runs $200-$600 depending on the scope, and it’s always quoted after we inspect the weld joint and the metal thickness. A weld repair is often far cheaper than a new fabricated gate, and we’ll tell you plainly which one makes sense.

Structural Crack Repair

A cracked weld at a corner or a rail is a structural failure, not cosmetic damage. It weakens the whole frame, and the operator’s force pushes against an unsupported joint every time the gate moves. We clean the joint, weld it properly, and check the surrounding frame for stress.

Hinge and Bracket Repairs

Hinge brackets take the most force of any part on a swing gate. When a bracket tears away, the gate drops and drags, which stresses the operator and speeds wear on everything else. We repair or replace the bracket and confirm the gate hangs correctly afterward.

Commercial Gate Repair

Commercial Gate Repair covers access gates at apartment complexes, storage facilities, small commercial lots, and HOA entries, where a stuck gate means traffic backup and, often, an open perimeter. Commercial gates usually run harder and longer than residential ones, so the operators, sensors, and safety edges wear out faster. We work with professional-grade commercial operators, including DoorKing and Elite systems, and we’re comfortable with the control boards and loop detectors those setups use. The work often involves access control, so we check the entire chain: the loop, the sensor, the operator, and the gate mechanics. Typical commercial gate repair in New Braunfels runs $250-$900 depending on the operator, the sensor or loop work, and whether the repair is mechanical or electrical. The estimate is free and the price is set in writing before we start.

Access Control and Loop Issues

When a commercial gate won’t open for a card or a code, the problem is frequently the loop detector or the reader, not the motor. We test the entire access chain and isolate the actual fault. That keeps you from paying for an operator replacement when a loop needs re-cutting.

Safety Edge and Sensor Failures

Commercial gates must reverse when they sense an obstruction, and a failed safety edge is a serious problem. We check photo eyes, safety edges, and reversing logic as part of the repair. If a sensor is dead, the gate may stop working for a reason that looks like a motor failure.

Iron Gate Repair

Iron Gate Repair handles the metal itself: bent pickets, rusted-through sections, broken scrollwork, and frames that have pulled out of square. Iron gates are heavy, and weight plus daily cycles plus the occasional bump from a vehicle will eventually show up as a bent frame or a broken joint. Rust is the slower threat. Hill Country humidity gets into small cracks and pin joints, and a spot that looks minor can turn into a rusted-through rail after a few seasons. We repair iron frames, straighten bent sections, and treat the joints that are prone to rust. Iron gate repair in New Braunfels typically runs $180-$500 depending on how much fabrication is involved, and we’ll tell you whether a repair or a new panel is the better value rather than defaulting to replacement.

Rust and Corrosion Repair

Rust starts at the joints, welds, and pin connections where water sits. We clean the affected area, repair the weakened metal if it’s structurally compromised, and protect the surface afterward. Catching rust at the surface stage saves a lot of money later.

Frame Straightening

An iron gate that gets hit or drops will go out of square, and a square frame matters more than it looks. An out-of-square gate binds against the post and overloads the operator. We straighten the frame and recheck the swing before we leave.

Sliding Gate Repair

Sliding Gate Repair resolves the problems owners of sliding gates actually face: the gate that jumps off the track, drags on the ground, or moves too slowly to be trusted. Sliding gates ride on a track and carriage, and when that track gets fouled with dirt, debris, or bent guides, the gate stops tracking correctly. A sliding gate that comes off its track is also a safety issue since a heavy sliding panel can crush or pinch. We inspect the track, carriage, rollers, and the operator, since a sliding gate failure often involves both mechanical and electrical parts at once. Sliding gate repair in New Braunfels typically runs $150-$450 depending on whether it’s track alignment, roller replacement, or an operator issue. We’ll diagnose it honestly and quote the work before we do it.

Track and Roller Problems

A sliding gate that shudders, drags, or makes noise usually has a track or roller problem. We clear the track, replace worn rollers, and realign the gate so it travels smoothly. Most of these failures get worse fast if you keep running the gate anyway.

Limit and Sensor Adjustments

A sliding gate that doesn’t open fully or reverses partway often has a limit switch or sensor out of adjustment. We test the full travel, reset the limits, and confirm the safety reverse actually works. This is usually a quick fix once the fault is isolated.

Wrought Iron Gate Repair

Wrought Iron Gate Repair restores decorative and ornate wrought iron gates where the value is as much visual as functional. These gates carry detail: scrolls, finials, decorative panels, and hand-formed joints, and a repair that ignores that detail leaves the gate looking damaged even when it works. We see wrought iron gates in New Braunfels where a section has rusted, a finial has broken off, or a decorative panel has bent. Repairs need to match the existing ornamental work rather than replace a section with a plain panel. We fabricate and weld to match the existing detail where it’s practical and rebuild joints so the gate locks up like it did originally. Wrought iron gate repair in New Braunfels typically runs $200-$650 depending on the ornamental detail involved. The free estimate includes a close look at the joints and finish.

Ornamental Detail Repair

Finials, scrolls, and decorative panels are often the first parts to break or rust through. We fabricate replacements that match the existing pattern rather than substituting a plain section. The goal is a gate that still looks like the one you bought.

Finish and Surface Work

Finish is a real part of wrought iron repair, not an afterthought. Once rust starts at a joint, the surrounding finish will fail unless the area is prepped and recoated. We address the surface after structural work is complete.

Metal Gate Repair

Metal Gate Repair covers the general category: gates built from steel, aluminum, and metal tube where the failure is mechanical, structural, or both. A metal gate that won’t shut, sags, or has a broken section falls into this work, whether it’s a swing gate or a sliding gate. Aluminum gates tend to fail at welds and brackets where the metal flexes under load. Steel gates are heavier, and their failures are more likely to be joint cracks or hinge problems. We repair the frame, replace broken sections, weld failed joints, and realign hardware. Metal gate repair in New Braunfels typically runs $180-$500 depending on the material and the scope. If a gate is failing at multiple points at once, we’ll tell you honestly whether a repair is worth it or whether a new gate makes more sense for your situation, since we install as well.

Weld and Joint Failures

Steel and aluminum gates fail at the joints when the gate flexes repeatedly under operator force. We repair the joints, check the surrounding frame, and reinforce any spot that failed because it was underbuilt. A good repair should outlast the original joint.

Hardware Replacement

Hinges, latches, stops, and brackets all wear out on metal gates. Replacing worn hardware is often what a gate needs most, and it’s far cheaper than frame work. We match the hardware to the gate’s weight and use geometry before we call it done.

Wood Gate Repair

Wood Gate Repair handles the timber side: gates that sag, drag, rot at the bottom rail, or have come apart at a joint. Wooden gates face a particular problem in New Braunfels, because our Hill Country humidity swells wood in the wet months and shrinks it in the dry ones, and that movement opens joints and lets water into the endgrain. The bottom rails and post contacts are the first to fail. A wooden gate that drags may need a hinge repair, a post adjustment, or a frame rebuild depending on what’s causing the sag. We repair frames, replace rotted rails, rehang or rehinge gates, and address the joints before they rot through. Wood gate repair in New Braunfels typically runs $150-$500 depending on the extent of the damage. If a wooden gate carries an operator, we check the mechanical side too, so the repair holds.

Rot and Moisture Damage

Endgrain at bottom rails and post contacts is where wood gates rot first, since that’s where water sits the longest after rain. We cut out the damaged section and replace it rather than covering over the rot. Addressing the endgrain properly makes a repair last far longer.

Sagging and Hardware

A sagging gate needs the cause identified before the hinge is tightened. Sometimes the hinge has worn, and sometimes the post has moved or the gate frame has gone out of square. We correct the actual cause, then recheck the swing and the latch.

Brands We Service

We work on the brand you already have, and that’s the whole point of hiring a gate specialist. Mighty Mule residential operators are common on DIY-installed gates, and we know where those units fail: the control board, the battery backup, and the limit settings. LiftMaster swing and slide operators on residential gates have their own known wear points, and we diagnose those to component level instead of replacing the whole unit. DoorKing and Elite systems show up on commercial and HOA entries, and those setups reward a technician who understands loop detectors, safety edges, and access control wiring alongside the motor.

Our brand coverage spans nine makers: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That range runs from entry-level residential kits through heavy-duty commercial operators, which is why we can service a gate that another outfit would look at and immediately declare a full replacement. We’re independent and experienced with each of these systems. Whether you have DoorKing equipment or any other make, we can help. If your gate is electrified and the fault is in the operator, look at our gate repair New Braunfels page for automated-system diagnostics.

Signs You Need a Pro Right Now

• The gate won’t reverse when something blocks it. A safety reverse that has stopped working is the one failure you shouldn’t run through. Stop using the gate and get it checked before someone gets hurt.
• The operator runs but the gate doesn’t move. This usually means a stripped gear, a broken arm, or a sheared pin inside the operator. Continued running wears the motor out and turns a cheap repair into an expensive one.
• The gate drags or sags when it swings. Dropping and dragging stresses the hinges, the post, and the operator at once. A gate that’s dragging is a sign something has already moved, and it gets worse each cycle.
• You hear a hum or a clicking and nothing else. That’s an electrical or control-board symptom rather than a mechanical one. Electrical work on a gate operator involves line voltage and shouldn’t be opened up by anyone without training.
• The gate has physical damage to the frame or post. A cracked weld, a torn bracket, or a bent post is a structural failure. It affects the gate’s alignment and its safety, and it needs a proper repair, not a patch.

Our Process, Step by Step

1. 1
   Call and describe the symptoms. Tell us what the gate is doing, the brand if you know it, and whether it’s automatic or manual. That conversation helps us bring the right parts and the right diagnostic approach on the first visit.
2. 2
   On-site diagnosis. We test the operator, controls, and gate mechanics together. That means checking motor function, limit switches, safety reverse, and the wiring and control board on automated units, plus the hinges, posts, and frame on the gate itself.
3. 3
   Straight answer on repair or replace. Once we know what failed, we tell you whether it’s a repair, and we explain what the repair covers. We don’t push a new gate when the old one can be fixed, and we don’t patch a gate that’s beyond saving.
4. 4
   Written estimate before work starts. You get the price in writing and you approve it before any work begins. The number on the estimate is the number you pay, and the written estimate sets the final price.
5. 5
   Repair, test, and walk-through. We complete the work, test the full travel, confirm the safety reverse, and show you what was done. You’ll know the gate works before we leave.

How Much Does Gate Repair Cost in New Braunfels?

Our Service Area Near New Braunfels

We serve New Braunfels and the surrounding towns, including Wimberley, Cibolo, Seguin, Schertz, Canyon Lake, Universal City, San Marcos, Converse, and Bulverde. Same-day dispatch is available for most repair calls, with fast dispatch from 7am to 7pm, Sunday through Friday. If your gate is in a nearby town and you’re not sure we reach you, call and we’ll confirm. For a wider view of our work, see our gate repair page for the Wimberley area and our gate repair page for Cibolo.

Frequently Asked Questions About Gate Repair in New Braunfels

Schedule Your Gate Repair Service in New Braunfels Today

Don’t keep working around a gate that won’t respond, drag, or reverse. Call (855) 939-0250 and describe what yours is doing. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 14 years of experience, and every visit comes with a free, no-obligation estimate and a price you approve before work begins. For new gate work, see gate repair.

Written by the team at Gate Repair New Braunfels.