Electric Gate Repair in New Braunfels - Fixed Today, No Surprise Invoice

Trusted Electric Gate Repair for New Braunfels Homeowners

When an automatic gate stops opening, the first thing you notice is the lineup of cars waiting on your side of the driveway. The second is that your property is now open to anyone who walks up. Electric gate repair in New Braunfels is what we do, and it’s the only thing we do. Our technicians have up to 14 years of experience working on both the mechanical side of a gate and the control and electrical side that makes it move, so we’re not guessing at which half of the system failed. We work on the brand you already have, whether it’s a LiftMaster swing operator at a home off Common Street or a DoorKing unit controlling access at a small commercial lot. Same-day service is often possible, and the price is always quoted and agreed before any work starts. Call (855) 939-0250 to get a technician out.

Call (855) 939-0250

Gate Opener Repair

Gate Opener Repair is the work of getting the unit that drives your gate – the motor, the control board, the arm or the chain – back to doing its job. You need it when the gate moves but won’t latch, when the opener hums and does nothing, when the remote works only from a few feet away, or when the gate reverses for no obvious reason. We diagnose the opener first rather than assuming the whole system is finished. If a control board, a limit switch or a worn drive gear is the culprit, we replace that part and leave the rest of your equipment alone. If a Mighty Mule arm on a residential driveway has simply reached the end of its life, we’ll tell you that too, and we install new gates as well, so you don’t need a second company. Typical Gate Opener Repair in New Braunfels runs $180 to $520 depending on the part and the operator, and the written estimate sets the final price.

Operator Diagnostics and Fault Codes

Most modern openers store a fault history that tells us exactly which safety input tripped and when. We read that before touching a single wire, which saves time and keeps you from paying for parts you didn’t need.

Arm, Chain and Drive Repairs

Swing arms wear at the pivot, and slide gates wear at the chain and the idler. We check alignment and travel limits as part of the repair, because a new part on a misaligned gate fails again quickly.

Automatic Gate Repair

Automatic Gate Repair covers everything that makes a gate operate on its own: the sensors, the safety edges, the loop detectors, the wiring between them, and the logic board that ties it together. You need it when the gate stops mid-travel, when it opens for a car that isn’t there, or when a safety reverse stops working and the gate no longer knows to back off an obstruction. Those are the calls we treat as urgent, because a gate that closes on a vehicle or a person is a real hazard. We test every safety device on the gate, not just the one that failed, and we walk the full travel of the gate to check for binding or a bent track. A typical automatic gate repair in New Braunfels falls between $200 and $650 depending on whether the problem is a sensor, a wiring run or the control board. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday.

Safety Edge and Sensor Testing

A photo-eye that’s dirty or knocked out of line will stop a gate as reliably as a dead motor. We realign and retest every beam, then confirm the reverse function actually works before we leave.

Wiring and Control Logic Faults

Rodent damage, water in a junction box and loose terminal screws cause more gate failures than motors do. We trace the circuit and repair the connection rather than selling you a new operator.

Electric Gate Motor

The Electric Gate Motor is the gearmotor itself, the component that turns electrical power into the force that swings or slides your gate. It needs attention when it growls, runs hot, leaks oil, moves slowly, or stops partway and needs a push to finish. Those symptoms usually point to worn brushes, a failing capacitor or a gearbox that’s losing its lubrication, and they get worse if you keep running the gate. We test the motor under load and check the current draw, because a gate that’s binding can make a healthy motor look bad. If the motor is sound, we fix the gate’s mechanical drag instead. If it’s genuinely done, we’ll show you why before we recommend a replacement operator, and we install new gates when that’s the honest answer. Expect $250 to $700 for motor-level electric gate repair in New Braunfels, with the exact figure set by the written estimate after we’ve inspected it.

Gearbox and Capacitor Failures

A weak start capacitor makes a motor act like it’s dying when it isn’t. We test the capacitor and the gearbox separately so the diagnosis lands on the right part the first time.

Load Testing and Current Draw

Measuring how many amps the motor pulls through a full cycle tells us whether the problem is the motor or the gate itself. That single reading often changes the whole repair plan.

Gate Access Control

Gate Access Control is the layer that decides who gets through: keypads, card readers, vehicle loop detectors, intercoms and the entry codes your household or tenants use. You need help with it when a code stops working, when the keypad lights up but won’t accept input, when a loop fails to detect a car sitting on it, or when you’ve changed tenants and need old codes removed for good. We service access control on both residential and small commercial systems, and we can add or reprogram entry devices on equipment you already own. Anyone who manages a shared driveway in New Braunfels knows how quickly a stale code list becomes a security problem. Access control work is measured and scheduled rather than rushed, and a typical job runs $150 to $450 depending on the devices involved. We’ll give you a free estimate and a written price before anything gets ordered.

Keypads, Readers and Intercoms

A keypad that’s weathered or full of moisture will fail intermittently before it dies completely. We test the unit and the wiring behind it, then reprogram or replace it.

Loop Detectors and Exit Devices

An exit loop buried in the driveway can fail from a pavement crack or a bad splice at the edge. We test the detector at the board before anyone cuts concrete.

Commercial Gate Operator

A Commercial Gate Operator is a heavier-duty unit built for constant cycles, and it needs a technician who understands cycle ratings rather than a residential installer stretched past their range. You need service when a property entrance starts stalling at peak hours, when the operator overheats and shuts down, or when a barrier arm at a lot entrance stops raising for paying customers. We work on professional-grade operators from FAAC, BFT and DoorKing alongside residential brands, so a commercial property manager doesn’t have to hunt for a separate vendor. We check the cycle count, the brake, the drive chain and the reversing logic, because commercial failures are usually wear plus load, not one bad part. Commercial gate operator repair in New Braunfels typically runs $350 to $900 depending on the operator and the parts. That’s estimated, and the written estimate you approve before work starts sets the final price.

Cycle Count and Duty Rating Review

An operator rated for a handful of cycles an hour will fail early on a busy entrance. We read the cycle history and tell you if the unit is undersized for the traffic it sees.

Barrier Arms and High-Traffic Entrances

Barrier arm operators take a beating at lot entrances. We check the arm balance, the breakaway bracket and the loop logic so the gate keeps clearing traffic through the day.

Brands We Service

We’re independent, which means we work on the brand you already have rather than steering you toward whatever we happen to install. We service LiftMaster swing and slide operators and know where their control boards and limit switches tend to fail first. We work on Mighty Mule and Ghost Controls units common on residential driveways, and we’re honest when an entry-level DIY operator has reached the point where repair costs more than it’s worth. On the heavier side, we handle FAAC and BFT operators and know their gearboxes and reversing systems well.

We also service Linear, Viking, Elite and DoorKing equipment, including DoorKing access systems at commercial entrances and Elite slide operators on longer residential runs. Nine brands, residential through commercial-grade, and our technicians have up to 14 years of experience across them. Being brand-agnostic is a diagnostic advantage: when we say a part has failed, it’s because we tested it, not because we only know one make. Whether you have LiftMaster or any other make, we can help. If your gate brand isn’t one we’ve named, call us and we’ll tell you straight whether it’s in our range.

Signs You Need a Pro Right Now

• The gate reverses or stops for no reason. Intermittent reversing usually means a safety device is failing or misaligned. It’s the one symptom worth calling about before it becomes a collision.
• The operator hums but the gate doesn’t move. A humming motor with no travel points to a seized gearbox, a bad capacitor or a bound gate. Running it longer can burn out a motor that was still repairable.
• You hear grinding or squealing during travel. Metal-on-metal noise means wear is already happening inside the drive. Catching it early keeps the repair to a part instead of a whole operator.
• The gate drifts open on its own or won’t stay closed. That’s a limit or logic fault, and it leaves your property open whether you’re home or not. It’s a scheduling priority for us.
• Keypad codes or remotes stop working. Sometimes it’s a battery. Often it’s a failing receiver or a corrupted code list. We test the device before recommending a replacement.

Our Process, Step by Step

1. 1
   Call and describe the symptom. We ask what the gate is doing, what brand the operator is, and whether it’s swing or slide. That first conversation tells us what parts and tools to expect, and it helps us book the right amount of time.
2. 2
   On-site diagnosis. We test the operator, the safety devices, the wiring and the gate’s mechanical travel. We read fault codes where the unit stores them and measure motor current under load, because those readings separate an electrical fault from a mechanical one.
3. 3
   Written estimate before any work. You get the diagnosis in plain terms and a price for the repair. Nothing gets ordered and nothing gets touched until you approve that number. If we find a second issue while we’re in there, we come back to you before doing anything about it.
4. 4
   The repair itself. We replace the failed part, realign what’s out of line, and retest the full cycle. Safety devices get tested last, because a gate that runs perfectly but won’t reverse isn’t fixed.
5. 5
   Walkthrough and honest guidance. We show you what failed and what we did. If the equipment is nearing the end of its life, we’ll say so and talk through repair versus replacement without pushing you toward a new gate you don’t need.

How Much Does Electric Gate Repair Cost in New Braunfels?

Our Service Area Near New Braunfels

We serve New Braunfels and the surrounding towns, including Seguin, Schertz, Cibolo, Canyon Lake, Bulverde, San Marcos, Universal City, Converse and Wimberley. Response times vary by distance and by how booked the day is, so we’ll give you a realistic window when you call rather than a number we can’t back up. If you’re outside New Braunfels, we can still help with electric gate repair and the towns around it, and we’ll confirm your address when you get in touch. For general gate work beyond the electrical side, our gate repair New Braunfels page covers the full picture.

Frequently Asked Questions About Electric Gate Repair in New Braunfels

Schedule Your Electric Gate Repair Service in New Braunfels Today

If your gate is stuck open, reversing on its own or refusing to move at all, don’t wait for it to get worse. Call (855) 939-0250 and we’ll get a gate technician out to look at it. Same-day service is often available, we work on the brand you already have, and the price is quoted and agreed before any work starts. You get a free, no-obligation estimate and a straight answer on whether repair or replacement makes more sense. We answer 24/7.

Written by the team at Gate Repair New Braunfels.